3 Ways To Make A QuickFire In The Wild

When you are in the wild, there is a likely chance that your lighters and matches have gotten wet, which are the only source for you to make a quickfire in the wild. So, if you do not know how to light up a quickfire in the wild, then you should stop calling yourself a survivor. In simple words, having the knowledge of lighting up a flame without the help of matches or lighters is a fundamental survival skill.

Even if you are not planning on going away from civilization, knowing the technique of making fire can impress people surrounding you. Hence, this article will provide you with a survival guide on three ways to make a quickfire in the wild, so your chances of lasting in the wild could increase. Also, to learn more fundamental survival skills to save your life in the wild, check out, https://theskilledsurvivor.com/ as this site has all the guides you need to survive in the wild.

Fire Plow

This is one of the common methods of making quick-fire in the wild, and it uses minimal tools. You only need a softer wood for plow board and harder wood for plowing. To be a skilled survivor, you must know this technique as you will be using this technique in harsh conditions with next to no tool for use.

Steps for Producing the Fire through Fire Plow

  • First of all, find a suitable fireplace for using this method. A fireplace should be as dry as it can be.
  • Then cut a groove about eight inches long and one inch wide. After doing that, find a piece of hardwood that should be one foot long and carve it to make a pointy end.
  • After collecting all the things, you will have to start rubbing, just like you saw in the movies. Take the head of your plow, and put it on your fireboard. Begin rubbing the pointy tip of your plow back and forth on the grove. This will help you create small pits of dust which are the essential part of producing the quickfire in wild.
  • Slow down your plowing so you can start collecting more and more dust at the bottom of your fireboard without wasting it.
  • When you can see a small pile of dust has been collected then intensify the motion of rubbing. Rub the plow with a lot of force and lower it down if you feel you are going to break it. Keep doing it till you see your dust smouldering.
  • At last, you just have to transfer the flame which you smouldered from the dust on tinder. Gently blow a little on the flame, and there you go, you have created a quickfire in the wild to survive.

Fire Plow is a little bit difficult method, and you should only use it when you do not have enough supplies as this process can take you a lot of time to produce a fire. And, we all know wasting time in the wild should not be on our survival guide to-do list.

The Hand Drill

The hand drill will help you start a fire with sticks if you’re interested in learning it. Hand drilling is a primitive technique, which is the most difficult to execute. In order to start a hand drill, shaft revolution and descending weight are of the utmost importance. It will take strength, determination, and wood to pull off this method of making a quickfire in the wild.

Steps for Producing the Fire through the Hand Drill

  • Create a nest out of tinder. Getting a quickfire going, requires the use of tinder. You can make tinder nests from leaves, grass, or bark that will burn effectively.
  • Put your best foot forward. Create a depression on the fireboard and cut an angular notch.
  • The bark should be placed below v-shaped cuts. From the erosion between the axle and fireboard, the bark is used to get an ember.
  • Spinning begins. Into the groove of the fireboard, insert the shaft. To work properly, your shaft should be about two feet long. As you roll the shaft down the axle, maintain weight on the fireboard. The ember must light on the fireboard before you can continue.
  • Set a quickfire to it. To place your shining ember on the bark, tap the fireboard. The bark can be exchanged for tinder. Get yourself fire by slowly blowing it.

Stone and Steel

Using matches, lighters, or sticks to start a quick fire is not essential. Fencing is a traditional method of starting fires in the open air. It might even be used at a regular campground for starting a fire. It’s usually a good idea to take flint and steel on any outdoor adventure. Around the world, a variety of armed forces make use of it.

Steps for Producing the Fire through Stone and Steel

  • Build your nest of tinder. The purpose of the nest is to catch sparks from your flint and steel.
  • Starter kits are available. As you hold the striker in one hand, grasp the steel in the other.
  • There is a strike. To prevent the quickfire steel from moving, position it against your base. Once the striker has been positioned on the fire steel, simply push it down in one smooth motion.
  • Get a fire going! Blow slowly on the ember to make a Quick Fire in Wild


When making a quickfire in the wild without a match, it’s important to consider the three points above in the survival guide. You should always have tinder and at least three tools with you when you go camping or hiking.

Make sure you do not build your fire near pine needles, peat soil, or other potential sources of ignition. You could endanger the environment and wildlife by carelessness, and you could also become stranded in a fire you started, worsening your survival situation. You should be in as clear an area as possible.

Lastly, before going to sleep put sprinkles of water on your fire to lower it a notch. This way you will be saved from animals, and you will not have to make a new fire when you get up in the morning.

Shumail Asad
Wouldn't you want the articles you are reading, to be written by a professional, charismatic writer, who dedicates his time to write what's best for the community's knowledge, then you are looking at that writer's bio right now. Striving to get what's best for our viewers is my motive. Talking about my education, I did my master's in English literature from the University of South Asia. I have done many jobs, including consultant to my novel writers, and book publishing companies. Content writer for many blogs. So what are you waiting for, read my other blog articles too, to enable your knowledge to get enhanced.